9/29/18

FMVSS 111 Explained with 2018 Updates | NTEA 2018



FMVSS (Federal Motor Vehicle Safety Standards) 111 is a law coming into full effect on May 1st 2018 which requires a minimum view behind a vehicle which has a gross weight of 10,000 pounds or lower. Watch to learn all the details involved and how backup cameras can help your vehicle be compliant with this new regulation.

9/27/18

Up-Tite Cargo Control - Tie Down Points... Where You Need Them!

Discovered at the 2015 ICUEE Show in Louisville, KY, Up-Tite cargo control system mounted on a Monroe Custom Service Body. This is a unique product found on many utility company bodies. It is very easy to locate or relocate hooks or tie downs where you need them.  Here are a few variations of the product carrying tools or securing loads.


 




Find out how it works at:

http://up-tite.com/HowItWorks/tabid/1493/Default.aspx

http://www.up-tite.com/

9/25/18

VMAC G30 SOLVES COMMON AIR COMPRESSOR CHALLENGES

Common Air Compressor Challenges


To celebrate the recent launch of the VMAC G30 Gas Engine Driven Air Compressor, now powered by Honda, VMAC ran a G30 Giveaway Contest. (Watch the video on our Facebook page!) In this contest we asked entrants to answer three simple questions. One of these questions asked fleet managers and operators what their top challenges with their current truck-mounted air compressors are. Here are the results:

Common Air Compressor Challenges

With seven options to choose from, the top three results were size, air output and weight, accounting for almost 60% of the responses. The VMAC G30 was designed and engineered to address the concerns fleet managers and operators have with their current equipment.

SIZE

VMAC G30 Gas Drive Air CompressorAir compressor size was the number one challenge our survey identified. The VMAC G30 is 50% smaller* than other competitive air compressors, measuring just 34” (l) x 21.5” (w) x 24” (h), making it small enough to fit on the side pack of a single rear wheel service body. The compact size frees up to 15 cubic feet on the truck body, and leaves more room in the back of the truck for supplies, tools, and equipment. Another bonus is that visibility is improved, as the short height of the G30 means it won’t obstruct the view in the rear window.

VMAC G30 Gas Drive Air Compressor

AIR OUTPUT

Not only is the G30 compact, it is also powerful—50% more powerful* than other competitive air compressors. Producing 30 CFM 100% of the time, the G30 can operate at 100% duty cycle, which means you won’t have to wait for air to build, and you can work without interruption, thanks to continuous air supply. The G30 doesn’t need a large air receiver tank either, which aids in the size challenge.

WEIGHT

Weight challenges are minimized with the VMAC G30, which weighs 50% less* than other competitive air compressors. Weighing just 205 lbs (93 kg), the G30 is over 200 lbs lighter. Not only does every pound of GVW count when building a truck service body, especially because vehicle weight restrictions vary by state, but the Environmental Protection Agency reports that for every 100 lbs of weight reduction, a vehicle’s fuel economy can increase by up to 2%. This means that with 200lbs less weight, the VMAC G30 can save you up to 4% in truck fuel costs.

*Compared to competing 22 to 30 CFM reciprocating gas engine driven air compressors, with 30-gallon air receiver tank.

OPERATING IN COLD TEMPERATURES

Respondents in Canada and the Northeast and Midwestern states noted operating air compressors in cold temperatures to be particularly challenging. To ensure the air compressor can operate in extreme cold, a cold climate kit can be installed on the G30. The G30 with cold climate kit is proven to start-up at temperatures of -30°C (-22°F).**

**Due diligence and additional care may be required for prolonged operation in temperatures reaching below -15°C (5°F).

TRANSFERABILITY

The VMAC G30’s lightweight and compact design makes it easier to transfer than heavier air compressors weighing over 400 lbs. The lifting hook makes for easy installation on the service truck as well.

MAINTENANCE

The VMAC G30 is easy to maintain, with servicing recommended every 200 hours or every 6 months. The compressor is oil injected; oil forms a seal between the rotors so they don’t wear against each other. The G30 compressor doesn’t contain any gears, reed-valves, piston rings, or components that will fatigue or become fouled, which means with proper servicing and operation, the compressor should never require rebuilding. The G30 comes with a VMAC Lifetime Limited Warranty, and the reliable Honda GX390 engine comes with a 3-year warranty (limited).

OPERATING IN HOT TEMPERATURES

Operating air compressors in hot temperatures was a concern for some operators and fleet managers, predominately those located in areas like Texas, Virginia, Arizona, and California. The G30 is proven to operate at temperatures up to 40°C (104°F) and is protected by a compressor oil temperature switch that opens at 140°C (284°F) and shuts down and disables the engine until the oil temperature drops below 139°C (282°F).

MINIMIZE CHALLENGES WITH THE VMAC G30

Each of these seven challenges can be addressed with upgrading your air compressor to the VMAC G30 Gas Engine Driven Air Compressor. Not only is it 50% smaller, 50% lighter, and 50% more powerful, but it is also proven to operate in the most extreme climates. It’s also easy to transfer and maintain, allowing you to spend your time on the job, not struggling with your equipment.

Learn more about the VMAC G30, or find a dealer. You can also find a VMAC Sales Rep—they’ll be happy to answer your questions, and provide you with a demo of the air compressor, so you can see the G30 in action for yourself.

9/23/18

Harbor CraneMaster Body - West Coast Style Personalized to Meet Your Every Need...



CraneMaster bodies represent an open design that permits you to choose all the appointments to meet your every need when using 2,000-4,000 lb. cranes with capacity up to 12,000 ft.-lb. The west coast service body design is the preferred style for these cranes. Harbor has sorted out which cranes go with which bodies. Tell us what weight you are loading and what length of crane you need to get the job done (length in feet x weight in lb. = ft. lb.) and we’ll put you in the right combination. Then, we’ll help you choose from among the many options that will make this your personal design!

Find more at: www.htbi.net



9/21/18

How the Harbor Service Body with a Cargo Bed Enclosure Keeps Stuff Out-Of-Sight



This is an example of a new GMC 2500HD chassis upfitted with a Harbor 8' Service Body with a Forklift-Loadable Rack, Class IV Receiver, and a 3-Piece Cargo Bed Enclosure. It's a great way to keep your stuff accessible and yet out of sight. Ron Sadler is the Fleet/Commercial Manager at Lehmer's Buick-GMC in Concord CA. See more at http://www.lehmersgmc.com

9/19/18

CargoGlide Models and Features



The different models and features CargoGlide has to offer.

9/17/18

Tommy Gate Rear Camera Kits

Tommy Gate now has a new Rear Camera Sensor Bar Option  for Ford Superduty pickup liftgates.


The incorporation of rear camera technology in modern pickup trucks has rapidly increased over the past couple of years. According to a DOT mandate passed in 2014, all vehicles under 10,000lbs must be outfitted with the technology by May 2018.

In order to maximize liftgate versatility and compatibility with such technology, the Tommy Gate engineering team has designed a one-of-a-kind Rear Camera & Sensor Bar kit for many newer model trucks.

The application chart that lists available kits and their corresponding truck models has been updated to include some Ford Superduty models and may be viewed here.

Rear Camera Bar kits are application specific and only available for the newest pickup models. Tommy Gate will continue to release additional applications as future pickup models are released.



If you have any questions, feel free to contact your territory manager and/or customer service at 1-800-LIFTGATE.

Tommy Gate is always working to design, build, and improve upon the finest liftgates in the world.

9/15/18

Tommy Gate - V2 Series Operation



                                        Operational Video for the Tommy Gate V2 Series.

9/13/18

Harbor PHVAC Van Interior


Plumbing Heating and Ventilation service technicians need to carry bottles of Nitro, CO2 or Brazing torch gases to pressure test systems, purge a system, blow out coils, or solder or repair lines. 

The Electrical/Telecom package is designed to satisfy your need with a 3-tank holder mounted off the rear shelf  panel, four (4) drawer packs, and a lockable storage compartment for valuable components. 

How about adding a drop-down rack for your different size ladders that help you get to that system? Keep your tanks at 40 cu.ft. or less if you have to carry them up the ladder!

Learn more at: http://htbi.net/


9/09/18

WeldMaster Truck Body - For the Jack of All Trades!


The urban welder is a jack of all trades. A little of this, and a little of that. And, of course, his or her work always includes some welding. Harbor created a jack of all trades truck just for her or him.  A service body with a welders edge!
  • 63-inch raised and vented front compartment with bottle brackets and rings inside to hold standard sized oxygen and acetylene tanks
  • Stainless Steel self-opening pop-top lids w/ body length compartment bins & 4" dividers
  • Push Button locking system with red band locking indicator
  • Modern gas shocks on each side opening door to keep them open during loading and unloading
  • 8" deep recessed bumper for sure footing when entering bed
  • Armless and self supporting tailgate work table
  • Adjustable, but lockable, shelving system
  • Weather shield system around locks, doors, and hingles, preventing leaks and securing the tools of your trade. Neoprene door seals, water-proof gaskets, self-sealing stainless steel rivets, and silky smooth three-point door latches with Teflon glides.

9/07/18

Carry It On Top - Masterack Ladder Racks for Every Type of Commercial Van


Masterack has a ladder rack for every type of commercial van, plus accessories to customize a package to your particular need. Choose from the original Masterack Locking Rack, the ergonomic Slide-Down Rack, the effortless PowerRack, or the economical heavy-duty Utility Rack.
 

To find out more, you may call Harbor Truck Bodies at 800-433-9452.
Also find us at http://htbi.net/

9/05/18

DECKED 101 | (Almost) Everything You Need to Know about DECKED



This is a deep dive into DECKED pickup truck and cargo van storage systems : exploring what it does for the customer, how it's constructed, its features and benefits, as well as assembly/installation best practices. While this is intended for DECKED retailers this is also a helpful guide for interested customers as well.

For more info on DECKED visit https://decked.com/

9/03/18

More Storage Capacity with the Traverse Compartment



Jordan shows us a unique change to an 8' Service Body that makes it so much more useful and effective in the same space. It's not a bigger body, but a substantially more effective one. The transverse compartment is part of the magic, and then combine that with the horizontal series long horizontal compartment, add the master lock system, Harbor's push-button locking system, stainless steel lids and this changeup creates magic when it comes to functionality and effectiveness.

See more at http://www.DowLewisTrucks.com

9/01/18

VMAC G30 SOLVES COMMON AIR COMPRESSOR CHALLENGES

Common Air Compressor Challenges


To celebrate the recent launch of the VMAC G30 Gas Engine Driven Air Compressor, now powered by Honda, VMAC ran a G30 Giveaway Contest. (Watch the video on our Facebook page!) In this contest we asked entrants to answer three simple questions. One of these questions asked fleet managers and operators what their top challenges with their current truck-mounted air compressors are. Here are the results:

Common Air Compressor Challenges

With seven options to choose from, the top three results were size, air output and weight, accounting for almost 60% of the responses. The VMAC G30 was designed and engineered to address the concerns fleet managers and operators have with their current equipment.

SIZE

VMAC G30 Gas Drive Air CompressorAir compressor size was the number one challenge our survey identified. The VMAC G30 is 50% smaller* than other competitive air compressors, measuring just 34” (l) x 21.5” (w) x 24” (h), making it small enough to fit on the side pack of a single rear wheel service body. The compact size frees up to 15 cubic feet on the truck body, and leaves more room in the back of the truck for supplies, tools, and equipment. Another bonus is that visibility is improved, as the short height of the G30 means it won’t obstruct the view in the rear window.

VMAC G30 Gas Drive Air Compressor

AIR OUTPUT

Not only is the G30 compact, it is also powerful—50% more powerful* than other competitive air compressors. Producing 30 CFM 100% of the time, the G30 can operate at 100% duty cycle, which means you won’t have to wait for air to build, and you can work without interruption, thanks to continuous air supply. The G30 doesn’t need a large air receiver tank either, which aids in the size challenge.

WEIGHT

Weight challenges are minimized with the VMAC G30, which weighs 50% less* than other competitive air compressors. Weighing just 205 lbs (93 kg), the G30 is over 200 lbs lighter. Not only does every pound of GVW count when building a truck service body, especially because vehicle weight restrictions vary by state, but the Environmental Protection Agency reports that for every 100 lbs of weight reduction, a vehicle’s fuel economy can increase by up to 2%. This means that with 200lbs less weight, the VMAC G30 can save you up to 4% in truck fuel costs.

*Compared to competing 22 to 30 CFM reciprocating gas engine driven air compressors, with 30-gallon air receiver tank.

OPERATING IN COLD TEMPERATURES

Respondents in Canada and the Northeast and Midwestern states noted operating air compressors in cold temperatures to be particularly challenging. To ensure the air compressor can operate in extreme cold, a cold climate kit can be installed on the G30. The G30 with cold climate kit is proven to start-up at temperatures of -30°C (-22°F).**

**Due diligence and additional care may be required for prolonged operation in temperatures reaching below -15°C (5°F).

TRANSFERABILITY

The VMAC G30’s lightweight and compact design makes it easier to transfer than heavier air compressors weighing over 400 lbs. The lifting hook makes for easy installation on the service truck as well.

MAINTENANCE

The VMAC G30 is easy to maintain, with servicing recommended every 200 hours or every 6 months. The compressor is oil injected; oil forms a seal between the rotors so they don’t wear against each other. The G30 compressor doesn’t contain any gears, reed-valves, piston rings, or components that will fatigue or become fouled, which means with proper servicing and operation, the compressor should never require rebuilding. The G30 comes with a VMAC Lifetime Limited Warranty, and the reliable Honda GX390 engine comes with a 3-year warranty (limited).

OPERATING IN HOT TEMPERATURES

Operating air compressors in hot temperatures was a concern for some operators and fleet managers, predominately those located in areas like Texas, Virginia, Arizona, and California. The G30 is proven to operate at temperatures up to 40°C (104°F) and is protected by a compressor oil temperature switch that opens at 140°C (284°F) and shuts down and disables the engine until the oil temperature drops below 139°C (282°F).

MINIMIZE CHALLENGES WITH THE VMAC G30

Each of these seven challenges can be addressed with upgrading your air compressor to the VMAC G30 Gas Engine Driven Air Compressor. Not only is it 50% smaller, 50% lighter, and 50% more powerful, but it is also proven to operate in the most extreme climates. It’s also easy to transfer and maintain, allowing you to spend your time on the job, not struggling with your equipment.

Learn more about the VMAC G30, or find a dealer. You can also find a VMAC Sales Rep—they’ll be happy to answer your questions, and provide you with a demo of the air compressor, so you can see the G30 in action for yourself.